F13 Hisense washer: door locking fault
Reviewed 2026-11-18 against 3 Hisense manuals. See sources.
Disclosure: this page has spots for parts links. When those links go live, we may earn a commission if you buy through them, at no extra cost to you. It doesn’t change what we recommend.Read the full disclosure.
What F13 means
F13 is Hisense’s “door locking fault.” The door is closed but the lock won’t engage. The washer won’t start a program until the door is closed and locked. [1, p. 58; 1, p. 40]
A related code, F14, is the opposite problem: the door is closed but won’t unlock. Hisense’s advice is to turn the washer off and on, and call a technician if F14 stays. [1, p. 58]
Safety first
- Don’t force the door while the door-lock icon is lit. [1, p. 42]
- Hisense provides an emergency door-release lever behind the pump filter cover, but only for situations like a power failure. Use it only when the drum has stopped, the water isn’t hot and the water level is below the door opening, and never during normal operation. [1, p. 48]
- Turn off the power before you clean around the door gasket. [1, p. 49]
Step-by-step owner checks
Close the door firmly
Open the door and shut it again firmly. A door that isn’t fully closed is the first thing Hisense says to check when the washer stops or won’t start. [1, p. 55]
Clear the door seal and glass
Look around the rubber gasket and the door glass for threads, hair or other debris. Hisense says to keep both clean and warns that debris caught in the door, or a door that isn’t fully closed, can cause a leak. [1, p. 12]
Don’t overstuff the drum
Hisense says the drum shouldn’t be packed tight and the door should close easily. If you have to push laundry in to shut the door, take some out. [1, p. 56]
Restart the washer
Turn the washer off, turn it back on, and restart the program. This is Hisense’s own first fix for F13. [1, p. 58]
Parts involved
Door lock
Locks the door during a cycle. F13 means it didn’t lock. Hisense doesn’t list an owner repair for this part and says to call a technician if F13 survives a restart. [1, p. 58]
[PLACEHOLDER affiliate link: “Door lock” for Hisense washer. No affiliate ID yet]Hisense’s manual names the fault (door locking) but not a specific replacement part number. Door lock parts are model-specific, so match the part to the model on your washer’s nameplate. Hisense says to use only manufacturer-approved spare parts. [1, p. 59]
When to call a pro
- F13 is still there after you have closed the door firmly, cleared the gasket and restarted the washer. [1, p. 58]
- The door won’t unlock (F14) after you turn the power off and on. [1, p. 58]
- The door is damaged, or the latch won’t catch at all.
- The washer is still under warranty. Hisense says the owner is responsible for any consequences of non-authorized repairs. [1, p. 55]
Hisense prints its service phone number on the front of each manual. Have the model and serial number from the nameplate ready when you call.
Common questions
What does F13 mean on a Hisense washer?
F13 is Hisense’s door locking fault. The door is closed but the lock didn’t engage, so the program can’t run.
What is the difference between F13 and F14?
F13 means the door won’t lock. F14 means the door is closed but won’t unlock.
How do I get clothes out if the door won’t open?
Hisense provides an emergency release lever behind the drain pump cover for situations like a power failure. Use it only when the drum has stopped, the water isn’t hot and the water level is below the door opening. Put the lever back afterward.
Other Hisense washer codes
Sources
- Hisense Canada, User's Operation Manual, WF5S2845BW front-load washer (models: WF5S2845BW (24 in., 3.1 cu. ft., 120 V)). PDF · support page. Accessed 2026-11-18. North American (120 V) manual. Page numbers are the printed page numbers in the English section.
- Hisense Malaysia, User's Operation Manual, WF105M3 washer (models: WF105M3, WF105M3*). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm that the code meanings match across Hisense front-load washers.
- Hisense New Zealand, User's Operation Manual, HWF5I9014 washer (models: HWF5I9014, HWF5I9014B, HWF5I9014W2/W3, HWF5I9014B2/B3). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm the code meanings and the "Confirm Start" step on newer controls.
Code meanings come from the Hisense WF5S2845BW manual (sold in Canada, 120 V) and match the Hisense WF105M3 and HWF5I9014 manuals. Hisense says some codes only apply to certain models, so check the fault table in your own manual too. Wording on this page is our own summary of those documents. Points without a citation are our general advice on when to stop and get help, not manufacturer statements.