F03 Hisense washer: water outlet (drain) fault
Reviewed 2026-11-18 against 3 Hisense manuals. See sources.
Disclosure: this page has spots for parts links. When those links go live, we may earn a commission if you buy through them, at no extra cost to you. It doesn’t change what we recommend.Read the full disclosure.
What F03 means
Hisense calls F03 a “water outlet fault.” The washer tried to pump water out and could not, so it stopped the program, sounded an alarm and put the code on the display. [1, p. 47; 1, p. 58]
Hisense lists three causes to check first: a pinched drain hose, a clogged drain filter, and a frozen drain hose. [1, p. 58; 2, p. 42]
Safety first
- If water is still in the drum, do not open the door until you have drained it through the drain pump filter. [1, p. 47]
- Let the water cool before you drain it. [1, p. 51]
- Turn off the power and the water faucets before any maintenance. Hisense warns that running a washer that is flooded because of a drain problem can cause electric shock or fire. [1, p. 49; 1, p. 12]
- Never open the pump filter while the washer is running. [1, p. 51]
Step-by-step owner checks
Check the drain hose for kinks
Follow the hose from the back of the washer to the drain. Make sure nothing is pinching, crushing or kinking it and the hose isn’t stretched tight. Straighten any bends you find. [1, p. 58; 1, p. 26]
Check where the hose ends
Hisense’s installation instructions say the end of the drain hose should be 24 to 58 inches (61 to 147 cm) above the bottom of the washer. They also say not to tape or seal the hose into the standpipe, because the connection needs an air gap. [1, p. 26]
If it’s freezing, thaw the drain hose
Hisense lists a frozen drain hose as an F03 cause. Its thawing method is to pour hot water into the drum, close the door, wait one to two hours, then run a spin-only cycle and watch that the water drains. [1, p. 58; 1, p. 54]
Drain the water and clean the pump filter
The pump filter is behind its own small cover on the washer. With the power off and the water cool, lay a towel down and put a container under the filter. If your model has a small emergency drain hose, pull out its plug and let the water run out first. Then turn the filter counterclockwise slowly and let any remaining water drain. Rinse lint and debris (coins, buttons, hairpins) off the filter under the tap. Screw it back in clockwise until it seals, keeping the seal surface clean. [1, p. 51]
Resume the cycle
Restore power and press Start/Pause to continue the program. [1, p. 58]
Parts involved
Drain pump filter
Hisense says to clean this filter when the washer won’t start its spin, or when buttons, coins, hairpins or other debris have got into the drain pump. [1, p. 51]
[PLACEHOLDER affiliate link: “Drain pump filter” for Hisense washer. No affiliate ID yet]Drain hose
Carries water from the washer to the standpipe or laundry tub. Hisense lists a pinched or frozen hose as an F03 cause. [1, p. 58; 1, p. 26]
[PLACEHOLDER affiliate link: “Drain hose” for Hisense washer. No affiliate ID yet]Hisense’s manual names only the hose and filter above. It doesn’t name an internal part behind F03. If the hose and filter are clear and the code keeps coming back, the fault is inside the machine and a technician needs to diagnose it. Hisense says to use only manufacturer-approved spare parts. [1, p. 59]
When to call a pro
- F03 comes back after you have cleared the hose and cleaned the pump filter. [1, p. 55]
- Water won’t drain even with the pump filter removed, or the filter won’t come out or reseal without leaking.
- There is standing water on the floor near the washer’s power cord or outlet. Leave the power off. [1, p. 12]
- The washer is still under warranty. Hisense says the owner is responsible for any consequences of repairs they do themselves or by non-authorized technicians. [1, p. 55]
Hisense prints its service phone number on the front of each manual. Have the model and serial number from the nameplate ready when you call.
Common questions
What does F03 mean on a Hisense washer?
F03 is Hisense’s water outlet (drain) fault. The washer couldn’t pump the water out. Hisense says to check for a pinched drain hose, a clogged drain filter or a frozen drain hose.
Can I open the door while F03 is showing?
Not while there’s water in the drum. Hisense says to drain the water through the drain pump filter first, after it has cooled.
How often should I clean a Hisense washer’s pump filter?
Hisense recommends at least once every two months, and more often after washing quilts, bath towels or old clothing.
Other Hisense washer codes
Sources
- Hisense Canada, User's Operation Manual, WF5S2845BW front-load washer (models: WF5S2845BW (24 in., 3.1 cu. ft., 120 V)). PDF · support page. Accessed 2026-11-18. North American (120 V) manual. Page numbers are the printed page numbers in the English section.
- Hisense Malaysia, User's Operation Manual, WF105M3 washer (models: WF105M3, WF105M3*). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm that the code meanings match across Hisense front-load washers.
- Hisense New Zealand, User's Operation Manual, HWF5I9014 washer (models: HWF5I9014, HWF5I9014B, HWF5I9014W2/W3, HWF5I9014B2/B3). PDF. Accessed 2026-11-18. Non-US model. Used only to confirm the code meanings and the "Confirm Start" step on newer controls.
Code meanings come from the Hisense WF5S2845BW manual (sold in Canada, 120 V) and match the Hisense WF105M3 and HWF5I9014 manuals. Hisense says some codes only apply to certain models, so check the fault table in your own manual too. Wording on this page is our own summary of those documents. Points without a citation are our general advice on when to stop and get help, not manufacturer statements.